Resistor for circuit breaker / battery 10 watts 3 ohm CNC machined body gold
Circuit breaker resistor:
- 3 ohm resistor
- 10 watts
- 6 to 24 volts
- CNC machined
- Gold anodised
- Drilled for mounting
- Lugs drilled to accept soldering wire
4,90€
16 in stock16 in stock
Resistor for electrical circuit breaker
To avoid feedback when the ignition is switched off
Resistor with pre-drilled support, terminals designed to accept bare solder wire
Better than the classic porcelain circuit-breaker resistor, without supports, with rigid wires that break…
CNC machined and gold anodised body
Technical specifications:
- Aluminium body
- CNC machining
- 10W
- 3 ohm
You may also like…
-
Electric sleeveRubber battery terminal covers, red and black 3 Sizes
Battery terminal covers:
- 3 sizes to choose from
- Protection against short circuits
- Used in automotive and industrial applications.
2 reviews3,50€Select options This product has multiple variants. The options may be chosen on the product page
Delivery expected on Thursday 24 April
If you order in the next 0 h and 50 min.
-
Switches and switch pads6-pole battery switch 12 volts 100 amps FIA + resistor
6-pole FIA circuit breaker:
- Voltage range: 0 to 27V
- Mechanical contact
- 2 power poles
- 4-pole contact
- Meets FIA standards
-
Maximum voltage: 100 amps
-
Switches and switch pads12V 25 Amp “Toggle Switch” for electrical circuits
12V ON / OFF switch:
- Max voltage: 48 volts
- Silver inner contact
- Supplied with rubber cap
- 4.8mm flat terminals
-
Max current: 25 amps
2 reviews -
High power connectorsHigh-power 600V 150 amp 1700 watt “Quick Disconnect” bulkhead connector
High-power bulkhead connector:
- CNC machined aluminium body, anodised
- Maximum voltage: 600 V
- Suitable for 20mm2 wire
- IP66 insulation
- Double stage cable gland
- Quick disconnect
-
Maximum current: 150 amps
Reviews about product
-
patrick E.
Published on 1 February 2025 at 10h59 (Order date: 20 January 2025 at 9h32)perfect . my old porcelain resistor had broken at the level of a wire so that’s why I turned to this model where I was able to solder the wires . it will be more reliable over time .
(Translated review) -
ASNAR F.
Published on 13 February 2024 at 18h03 (Order date: 25 October 2023 at 0h00)Very good
(Translated review)
Related products
-
Switches and switch padsStarter switch and ignition key 12 volts 30 amps
Key-operated starter switch:
- Operating voltage: 2 to 28 volts
- Maximum acceptable current: 30 amps
- Self-locking in position
- Temperature range: -30°C to +90°C
- Installation hole diameter: 24mm
- Supplied with 2 keys
-
Connection with 4 terminals on back
1 review -
Switches and switch padsPower distribution box with 12 PDM 12 volt switch board for complete wiring harness
Power distribution box + 12-switch board
- Supplied with resettable circuit breaker
- Switch Panel” look like a PDM
- 6-colour LED backlighting
- Up to 30 amps / switch
- Temperature range: -40°C to +85°C
- Tightness: IP67
- Supplied with full wiring diagram
- Simple, reliable and cost-effective
-
Equip your car like a factory WRC car or endurance prototype
-
Switches and switch padsPolarity reversing lever switch 6 terminals 12 volts
12-volt reversing switch:
- 3 positions ON – OFF – ON
- Self-holding in position
- Voltage range: 2 to 250 volts
- Maximum current: 15 amps
- Temperature range: -30°C to +90°C
- Installation hole diameter: 12mm
- Tightness: IP65
-
3 positions with dead centre
2 reviews -
Switches and switch padsON / OFF switch and circuit breaker for motocross bikes
ON / OFF button for motorbike:
- Operating voltage: 0 to 28 volts
- Maximum acceptable current: 30 amps
- Temperature range: -30°C to +90°C
- Diameter of standard motorbike handlebar clamp
- 50cm long harness with PVC sheath
-
Suitable for all motorbikes and scooters
